JG_TpsLabStudio_LTS/exe/apps/DevicesApp/commands/程控命令.xml

<?xml version="1.0" encoding="utf-8" ?>
<ScpiCommands>
  <Devices>
    <DeviceCommand DeviceType="信号源">
      <Models>
        <string>ESG-D3000B</string>
        <string>ESG-3000B</string>
        <string>E4421B</string>
        <string>E4432B</string>
      </Models>
      <Commands>
        <Command Key="仪器复位" Value=":SYSTem:PRESet" Description="{0}频率，单位MHz"/>
        <Command Key="设置频率" Value=":FREQ:CW {0} MHz" Description="{0}频率，单位MHz"/>
        <Command Key="设置功率" Value=":POW:AMPL {0} dBm" Description="{0}频率，单位MHz"/>
        <Command Key="射频开关开" Value=":OUTP:STAT ON" Description="单位V"/>
        <Command Key="射频开关关" Value=":OUTP:STAT OFF" Description="单位A"/>
        <Command Key="调制关" Value=":OUTP:MOD:STAT OFF" Description="{0}电流值，单位A，CC模式下"/>
        <Command Key="调制开" Value=":OUTP:MOD:STAT ON" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="Step扫描模式" Value=":LIST:TYPE STEP" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="Step扫描点数" Value=":SWEep:POINts {0}" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="单次扫描" Value=":INITiate" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="单次扫描模式" Value=":INITiate:CONTinuous OFF" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="开启Sweep扫频" Value=":FREQuency:MODE LIST" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="关闭Sweep扫频" Value=":FREQuency:MODE CW" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="扫描起始频率" Value=":FREQuency:STARt {0} MHz" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="扫描终止频率" Value=":FREQuency:Stop {0} MHz" Description="{0}电压值，单位V，CV模式下"/>
      </Commands>
    </DeviceCommand>

    <DeviceCommand DeviceType="噪声系数分析仪">
      <Models>
        <string>ESG-D3000B</string>
        <string>N8975A</string>
      </Models>
      <Commands>
        <Command Key="仪器复位" Value=":SYSTem:PRESet" Description="{0}频率，单位Hz"/>
        <Command Key="Center" Value=":FREQ:CENT {0}" Description="{0}频率，单位Hz"/>
        <Command Key="Span" Value=":FREQ:SPAN {0}" Description="{0}频率，单位Hz"/>
        <Command Key="Start" Value=":FREQuency:STARt {0}" Description="单位V"/>
        <Command Key="Stop" Value=":FREQuency:STOP {0}" Description="单位A"/>

        <Command Key="FIXFreqMode" Value="SENSe:FREQuency:MODE FIXed" Description="单位A"/>
        <Command Key="FIXFreq" Value=":FREQuency:FIXed {0}" Description="单位A"/>

        <Command Key="SweepPoint" Value=":SWEep:POINts {0}" Description="单位A"/>
        <Command Key="ContinuousMeasState" Value="INIT:CONT {0}" Description="单位A"/>
        <Command Key="CalState" Value="DISP:DATA:CORR {0}" Description="单位A"/>
        <Command Key="StoreStateFile" Value="MMEM:STOR:STAT 1, \'{0}\'" Description="单位A"/>
        <Command Key="LoadStateFile" Value="MMEM:STOR:STAT 1, \'{0}\'" Description="单位A"/>
        <Command Key="Measure" Value="INIT" Description="单位A"/>
        <Command Key="OPC" Value="*OPC?" Description="方法研究"/>

        <Command Key="下变频模式" Value=":CONFigure:MODE:DUT DOWN" Description="{0}电流值，单位A，CC模式下"/>
        <Command Key="USB边带模式" Value=":CONFigure:MODE:DOWNconv:LOSCillator:OFFSet USB" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="本振频率" Value=":CONFigure:MODE:DOWNconv:LOSCillator:FREQuency {0}" Description="{0}电压值，单位V，CV模式下"/>

        <Command Key="ReadNFIG" Value="FETC:CORR:NFIG?" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="ReadFIXedNFIG" Value="FETC:SCAL:CORR:NFIG?" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="SetFreqList" Value="FREQuency:LIST:DATA {0}" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="ReadFreqList" Value="FREQuency:LIST:DATA?" Description="{0}电压值，单位V，CV模式下"/>

        <Command Key="DUT后端补偿状态" Value="CORR:LOSS:AFT:STAT {0}" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="DUT前端补偿状态" Value="CORR:LOSS:BEF:STAT {0}" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="DUT后端补偿表模式" Value=":CORRection:LOSS:AFTer:MODE TABLe" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="DUT前端补偿表模式" Value=":CORRection:LOSS:BEFore:MODE TABLe" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="DUT后端补偿表" Value=":CORRection:LOSS:AFTer:TABLe:DATA {0}" Description="{0}数据以‘，’号分格"/>
        <Command Key="DUT前端补偿表" Value=":CORRection:LOSS:BEFore:TABLe:DATA {0}" Description="{0}数据以‘，’号分格"/>
        <Command Key="获取DUT后端补偿表" Value=":CORRection:LOSS:AFTer:TABLe:DATA?" Description="{0}数据以‘，’号分格"/>
        <Command Key="获取DUT前端补偿表" Value=":CORRection:LOSS:BEFore:TABLe:DATA?" Description="{0}数据以‘，’号分格"/>
        <Command Key="DUT后端热力学温度" Value=":CORR:TEMP:AFT {0}" Description="{0}数据以‘，’号分格"/>
        <Command Key="DUT前端热力学温度" Value=":CORR:TEMP:BEF {0}" Description="{0}数据以‘，’号分格"/>



      </Commands>
    </DeviceCommand>

    <DeviceCommand DeviceType="频谱仪">
      <Models>
        <!--<string>N9020A</string>-->
        <string>E4440A</string>
      </Models>
      <Commands>
        <Command Key="仪器复位" Value=":SYSTem:PRESet" Description="{0}频率，单位MHz"/>
        <Command Key="START" Value=":SENS:FREQ:STAR {0} MHz" Description="{0}频率，单位MHz"/>
        <Command Key="STOP" Value=":SENS:FREQ:STOP {0} MHz" Description="{0}频率，单位MHz"/>
        <Command Key="CENTER" Value=":SENS:FREQ:CENT {0} MHz" Description="{0}频率，单位MHz"/>
        <Command Key="SPAN" Value=":SENS:FREQ:SPAN {0} MHz" Description="{0}频率，单位MHz"/>
        <Command Key="REF" Value=":DISP:WIND:TRAC:Y:SCAL:RLEV {0} dBm" Description="单位V"/>
        <Command Key="RBW" Value="???" Description="单位A"/>
        <Command Key="VBW" Value=":BWIDth:VID {0}" Description="{0}电流值，单位A，CC模式下"/>
        <Command Key="VBWAUTO" Value=":BWIDth:VID:AUTO 1" Description="{0}电流值，单位A，CC模式下"/>
        <Command Key="PEAK" Value=":CALC:MARK{0}:MAX" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="MARK打开" Value=":CALC:MARK{0}:STAT ON" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="读MARK功率" Value=":CALC:MARK{0}:Y?" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="读MARK频率" Value=":CALC:MARK{0}:X?" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="设置MARK频率" Value=":CALC:MARK{0}:X {1} MHz" Description="{0}电压值，{1}频率点,单位V，CV模式下"/>
        <Command Key="设置MARK为NOISe" Value=":CALCulate:MARKer{0}:FUNCtion NOISe" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="设置MARK为常规" Value=":CALCulate:MARKer{0}:FUNCtion OFF" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="读曲线" Value="TRACe? TRACE1" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="读起始频率" Value=":SENS:FREQ:STAR?" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="读截止频率" Value=":SENS:FREQ:STOP?" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="最大保持开" Value=":TRACe1:MODE MAXHold" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="最大保持关" Value=":TRACe1:MODE WRITe" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="噪声模式" Value=":CALC:MARK:FUNC NOIS" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="关闭频谱仪自检" Value=":CALibration:AUTO OFF" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="AVER_ON" Value=":AVERage ON" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="AVER_OFF" Value=":AVERage ON" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="AVERCounts" Value=":AVERage COUNt {0}" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="DCmode" Value=":INPut:COUPling DC" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="ACmode" Value=":INPut:COUPling AC" Description="{0}电压值，单位V，CV模式下"/>
      </Commands>
    </DeviceCommand>
    <DeviceCommand DeviceType="程控电源">
      <Models>
        <string>IT6722</string>
      </Models>
      <Commands>
        <Command Key="打开电源" Value="OUTP 1" Description="{0}频率，单位MHz"/>
        <Command Key="关闭电源" Value="OUTP 0" Description="{0}频率，单位MHz"/>
        <Command Key="设置电压" Value="VOLT {0}" Description="{0}电压值，单位V"/>
        <Command Key="设置限流" Value=":CURR {0}" Description="{0}电流值，单位A"/>
        <Command Key="读取电压" Value=":MEAS:VOLT?" Description="单位V"/>
        <Command Key="读取电流" Value=":MEAS:CURR?" Description="单位A"/>
      </Commands>
    </DeviceCommand>
    <DeviceCommand DeviceType="电子负载">
      <Models>
        <string>IT8811</string>
      </Models>
      <Commands>
        <Command Key="打开负载" Value="SOUR:INP ON" Description="{0}频率，单位MHz"/>
        <Command Key="关闭负载" Value="SOUR:INP OFF" Description="{0}频率，单位MHz"/>
        <Command Key="读取电压" Value="FETC:VOLT?" Description="单位V"/>
        <Command Key="读取电流" Value="FETC:CURR?" Description="单位A"/>
        <Command Key="设置电流" Value="SOUR:CURR {0}" Description="{0}电流值，单位A，CC模式下"/>
        <Command Key="设置电压" Value="SOUR:VOLT {0}" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="设置恒流模式" Value="SOUR:FUNC CURR" Description=""/>
        <Command Key="设置恒压模式" Value="SOUR:FUNC VOLT" Description=""/>
      </Commands>
    </DeviceCommand>
    <DeviceCommand DeviceType="矢量网络分析仪">
      <Models>
        <string>E5062A</string>
      </Models>
      <Commands>
        <Command Key="仪器复位" Value=":SYSTem:PRESet" Description="{0}频率，单位MHz"/>
        <Command Key="驻波测试模式" Value="CALC{0}:FORM SWR" Description="{0}频率，单位MHz"/>
        <Command Key="S11" Value=":CALCulate{0}:PARameter{1}:DEFine S11" Description="{0}频率，单位MHz"/>
        <Command Key="S22" Value=":CALCulate{0}:PARameter{1}:DEFine S22" Description="{0}频率，单位MHz"/>
        <Command Key="打开Mark" Value=":CALC{0}:MARK{1} ON" Description="{0}频率，单位MHz"/>
        <Command Key="设置Mark位置" Value=":CALC{0}:MARK{1}:X {2}" Description="{0}频率，单位Hz"/>
        <Command Key="读取Mark数据" Value=":CALC{0}:MARK{1}:Y?" Description="{0}频率，单位MHz"/>
        <Command Key="MarkPeak" Value=":CALC{0}:MARK{1}:FUNC:EXEC" Description="{0}频率，单位MHz"/>
        <Command Key="Start" Value=":SENS{0}:FREQ:STAR {1}" Description="{0}频率，单位Hz"/>
        <Command Key="Stop" Value=":SENS{0}:FREQ:STOP {1}" Description="{0}频率，单位Hz"/>
        <Command Key="power" Value="SOUR:POW1 {0}" Description="{0}频率，单位Hz"/>
        <Command Key="outputON" Value="OUTP ON" Description="{0}频率，单位Hz"/>
        <Command Key="outputOFF" Value="OUTP OFF" Description="{0}频率，单位Hz"/>
        <Command Key="ATT" Value=":SOURce{0}:POWer:ATTenuation {1}" Description="{0}频率，单位Hz"/>

        <Command Key="ATT" Value=":SOURce{0}:POWer:ATTenuation {1}" Description="{0}频率，单位Hz"/>
      </Commands>
    </DeviceCommand>

    <DeviceCommand DeviceType="示波器">
      <Models>
        <string>DSO-X\s3024A</string>
        <string>DSO-X 3024A</string>
        <string>DSO-X 3054A</string>
      </Models>
      <Commands>
        <Command Key="RUN" Value=":RUN" Description="{0}频率，单位MHz"/>
        <Command Key="STOP" Value=":STOP" Description="{0}频率，单位MHz"/>
        <Command Key="Single" Value=":SINGle" Description="{0}频率，单位MHz"/>
        <Command Key="UNIT设置为Volt" Value=":CHANnel{0}:UNITs VOLT" Description="单位A"/>
        <Command Key="Scale" Value=":CHANnel{0}:SCALe {1}V" Description="单位V"/>
        <Command Key="通道offset" Value=":CHANnel{0}:OFFSet {1}V" Description="{0}电流值，单位V，CC模式下"/>
        <Command Key="50欧姆电阻" Value=":CHANnel{0}:IMPedance FIFTy" Description="{0}电流值，单位V，CC模式下"/>
        <Command Key="ACorDC" Value=":CHANnel{0}:COUPling {1}" Description="{0}电流值，单位V，CC模式下"/>

        <Command Key="TimeBase" Value=":TIMebase:SCALe {0}" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="POSition" Value=":TIMebase:POSition {0}" Description="{0}电压值，单位V，CV模式下"/>

        <Command Key="边沿触发" Value=":TRIGger:MODE EDGE" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="通道触发电平" Value=":TRIGger:LEVel {0}V,CHANnel{1}" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="触发斜率" Value=":TRIGger:SLOPe {0}" Description="{0}电压值，单位V，CV模式下,POS,NEG,EITH,ALT"/>
        <Command Key="触发源" Value=":TRIGger:SOURce CHANnel{0}" Description="{0}电压值，单位V，CV模式下"/>

        <Command Key="清除测量方法" Value=":MEASure:CLEar" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="相移测量" Value=":MEASure:PHASe" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="读取相移数据" Value=":MEASure:PHASe?" Description="{0}电压值，单位V，CV模式下"/>

        <Command Key="峰峰值测量" Value=":MEASure:VPP" Description="{0}电压值，单位V，CV模式下"/>
        <Command Key="读取峰峰值" Value=":MEASure:VPP?" Description="{0}电压值，单位V，CV模式下"/>

      </Commands>
    </DeviceCommand>

  </Devices>
</ScpiCommands>